Pressure cooker ribs are the quick solution to a tasty dinner!
Grass fed beef back ribs are normally cooked low and slow for many hours to break down the collagen in the tough meat. What if I told you you could get the same results in less than an hour in a pressure cooker? Seriously. Don’t be afraid of your pot exploding. If you get a good pressure cooker AND follow directions, you’ll save time and energy PLUS get kickass results. If you don’t…it was nice knowing you.
My Favorite Rub for Ribs
I love Chili 9000 on all sorts of stuff, but it’s my go-to dry rub for ribs.
Time to make Pressure Cooker Grass Fed Beef Back Ribs!
Serves 4
Ingredients:
- 1 rack of grass fed beef back ribs (~ 3.5 pounds)
- Dry rub of choice (I used Penzeys Chili 9000)
- Kosher salt
- ¾ cup water
- 4 ounces of unsweetened applesauce
- 2 tablespoons coconut aminos
- 1 teaspoon fish sauce
Method:
Grab a rack of grass fed beef back ribs and pat them dry with a paper towel. Then, sprinkle it liberally on both sides with the dry rub and kosher salt.
Wrap it up in foil to marinate for at least two hours and up to a day.
When you’re ready to cook the ribs, preheat the broiler with the rack positioned 4-6 inches from the heating element.
Grab the rack from the fridge and cut it so it’ll fit in your pressure cooker. If you’ve got a 6-quart pot, cut the rack into three even pieces. Put the ribs on a wire rack in a foil-lined, rimmed baking sheet.
Broil the ribs for 1-2 minutes on each side to get a nice char. Keep the broiler on because you’ll be broiling these meaty bones again at the end.
Add the water, applesauce, coconut aminos, and fish sauce to the pressure cooker. Stir to combine and add a rack to the pot.
Pile the ribs into the pressure cooker and lock on the lid.
Crank the heat to high and when the pot reaches high pressure, turn down the heat to maintain high pressure on the lowest setting possible. Cook on high pressure for 20 minutes and let the pressure come down naturally or release it quickly.
Remove the ribs and place them back on a wire rack atop a foil-lined, rimmed baking sheet.
Simmer the cooking liquid until it is reduced to 2 cups (~5 minutes). Skim off the excess fat at the top if desired and adjust seasoning.
Baste the racks with the braising liquid…
…and broil them for about a minute to get some crunchy bits.
With a minimal investment in time, you’ve got some finger-lickin’ tender ribs. Try it!
Looking for more recipe ideas? Head on over to my Recipe Index. You’ll also find exclusive recipes on my iPhone and iPad app, and in my cookbooks, Nom Nom Paleo: Food for Humans (Andrews McMeel Publishing 2013), Ready or Not! (Andrews McMeel Publishing 2017), and Nom Nom Paleo: Let’s Go! (Andrews McMeel Publishing 2021).
PRINTER-FRIENDLY RECIPE CARD
Pressure Cooker Grass Fed Beef Back Ribs
Ingredients
- 3.5 pound grass fed beef back ribs 1 rack
- dry rub of choice (I used Penzeys Chili 9000)
- Diamond Crystal kosher salt
- 3/4 cup water
- 4 ounce unsweetened applesauce
- 2 tablespoon coconut aminos
- 1 teaspoon fish sauce
Instructions
- Grab a rack of grass fed beef back ribs and pat them dry with a paper towel. Then, sprinkle it liberally on both sides with the dry rub and kosher salt.
- Wrap it up in foil to marinate for at least two hours and up to a day.
- When you’re ready to cook the ribs, preheat the broiler with the rack positioned 4-6 inches from the heating element.
- Grab the rack from the fridge and cut it so it’ll fit in your pressure cooker. If you’ve got a 6-quart pot, cut the rack into three even pieces.
- Put the chopped up ribs on a wire rack in a foil-lined, rimmed baking sheet.
- Broil the ribs for 1-2 minutes on each side to get a nice char. Keep the broiler on because you’ll be broiling these meaty bones again at the end.
- Add the water, applesauce, coconut aminos, and fish sauce to the pressure cooker. Stir to combine and add a rack to the pot.
- Pile the ribs into the pressure cooker and lock on the lid.
- Crank the heat to high and when the pot reaches high pressure, turn down the heat to maintain high pressure on the lowest setting possible.
- Cook on high pressure for 20 minutes and let the pressure come down naturally or release it quickly.
- Remove the ribs and place them back on a wire rack atop a foil-lined, rimmed baking sheet.
- Simmer the cooking liquid until it is reduced to 2 cups (~5 minutes). Skim off the excess fat at the top if desired and adjust seasoning.
- Baste the racks with the braising liquid and broil them for about a minute to get some crunchy bits.
Nutrition
Nutrition information is automatically calculated, so should only be used as an approximation.
I found the instructions for the pressure setting confusing. Crank the heat to high means What? Manual high pressure setting? When does it reach high pressure? And then how do you turn the heat down? Mine only has either high or low pressure and there’s no adjustment range for either setting.
I wrote this recipe for a stovetop pressure cooker. If you have an Instant Pot, just program it to cook for 20 minutes under high pressure.
I have a 2.5lb beef back ribs. How long should I program the instant pot?
Same amount of time!
Excellent recipe! I had an Applewood store-bought rub that I added a bunch of spices to to make it better and ,actually, ended up letting the ribs sit in the refrigerator for 2 days before cooking. I cut up some fresh apples since i didn’t have applesauce, too. But, wow, the flavor and texture of the meat was outstanding!
This recipe was delicious! My husband and I totally enjoyed it. Thank
you for posting it. 100% will be making it again.
Delicious! I’ve made this many times and always come back to this recipe. Thank you!